Introductory Information About Silicon Nitride Film Stress And Wafer Processing
by Jessica Gomez,
published:
syndicated: 2 | total views: 3139 |
word count: 642
laesbarhedsindex readability score: Very Difficult Readability
on the net: http://www.roguevalleymicro.com
UNITED STATES, Jul 07 — Low Stress LPCVD Nitride with a Film Stress of less than 250 MPa Tensile is often used for building Membranes, Cantilever Beams and other mechanical structures. Low Stress Nitride is also very effective as a KOH . The characteristics of silicon-nitride films deposited with plasma-enhanced chemical vapor deposition (PECVD) can vary in composition and physical properties. If additional compressive films such as PECVD Oxide are added on top of the nitride, additional stress must be built into the nitride to compensate for it
L
ow Stress LPCVD Nitride with a Film Stress of less than 250 MPa Tensile is often used for building Membranes, Cantilever Beams and other mechanical structures. Low Stress Nitride is also very effective as a KOH . The characteristics of silicon-nitride films deposited with plasma-enhanced chemical vapor deposition (PECVD) can vary in composition and physical properties. An important parameter in the fabrication of micro-electro-mechanical systems (MEMS) devices is the control and tailoring of the film stress. In fact, silicon-nitride film stress can vary from tensile (up to 800 MPa) to compressive (-500 MPa), depending on the PECVD deposition conditions.
One of the basic building blocks in silicon wafer processing and MEMS processing is the ability to deposit thin films of material onto a wafer. One such deposition process is LPCVD Silicon Nitride, a thin film deposition process that coats all of the exposed areas of the wafer. The difference in mechanical properties between the nitride and the silicon wafer will introduce a "stress" in the wafer + nitride system.
Tensile and Compressive Stress If there is an equal amount of nitride on both sides of the wafer it will be in a balanced state and remain flat.
If the nitride is removed from one side of the wafer the system will no longer be in equilibrium and the wafer will bow. If the wafer curves up toward the side with the nitride, the nitride is considered to be tensile. If the wafer curves down away from the side with the nitride, the nitride is considered to be compressive.
Selecting the Right Film Stress: Choosing the correct film stress can be crucial to yield and performance of the device. For instance, if Stoichiometric Nitride (800 Mpa Tensile) is used as a KOH mask, too thick of a film can lead to micro-cracking and film failure. Switching to a Low Stress NItride (200 Mpa Tensile) will eliminate micro cracking and improve yield.
Film Stress for MEMS: Having too low of a film stress can also cause problems for certain applications. Many MEMS foundry applications use silicon nitride as a membrane, diaphragm, or other suspended structure. Insufficient tensile stress can result in structures that can "sag" or "droop". Typically, the thinner the nitride, the more tensile stress is needed to keep a suspended structure flat.
Remember, the entire suspended structure must be considered a "system". If additional compressive films such as PECVD Oxide are added on top of the nitride, additional stress must be built into the nitride to compensate for it. The entire "system" must be tensile.
Applications Guide: Here are some of our nitride recommendations for select applications:
KOH Etch Mask: Nitride Thickness (500 to 3000 A)
Film type: stoichiometric Nitride On Oxide Stress
Target (-300/800 Mpa)
Nitride Thickness (500 to 10,000 A)
Film type: Low Stress Nitride Stress
Target (200 Mpa)
Nitride Thickness (500 to 30,000 A)
Film type: Super Low Stress Nitride Stress
Target (50 Mpa)
Suspended Structures: Nitride Thickness (Less than 500 A)
Film type: Low Stress Nitride Stress
Target (350 Mpa)
Nitride Thickness (500 to 1000 A)
Film type: Low Stress Nitride Stress
Target (300 Mpa)
Nitride Thickness (1000 to 5,000 A)
Film type: Low Stress Nitride Stress
Target (250 Mpa)
Nitride Thickness (5,000 to 10,000 A)
Film type: Low Stress Nitride Stress
Target (200 Mpa)
Nitride Thickness (10,000 to 15,000 A)
Film type: Low Stress Nitride Stress
Target (150 Mpa)
Nitride Thickness (15,000 to 20,000 A)
Film type: Super Low Stress Nitride Stress
Target (100 Mpa)
Nitride Thickness (20,000 to 30,000 A)
Communicate directly with Jessica Gomez, the author of this article. Ask questions, send suggestions, comments, engage in conversation, or perhaps you would like to submit a project.
Click Here to ask a question, send a comment, or proposal.
A fluke thermal camera is an infrared camera device that detects heat and temperature changes within a room. These are often hand held for easily portability and allow building inspectors to carry out the necessary safety and energy efficiency checks
Most Network Managers know that microwave radio links require a clear line of sight and access to spectrum, but to achieve a successful link that is going to deliver service 99.999% of the time the devil is in the detail.
With so many people fighting the economic downturn, many are trying to figure out how to remain in their chosen field and become even more valuable. There are a few ways to move forward, and they’re not always easy to identify, which is why man
There are many people interested in smart phones who do not want to buy Apple iPhones, but up until now, there haven’t been a whole lot of options that can compare. However, Microsoft seems poised to give the smart phone market their best shot.
There is a distinct need for a standardized technology platform for applications that manage small amounts of data with low radio traffic and ultra-low-power management. The solutions are an avenue for VARs, integrators and manufacturers to offer cos
Toshiba REGZA 32-inch AV series combines HD Ready picture processing with a stylish contemporary black high gloss design. The 32-inch Regza AV series includes Resolution+ technlogy enhancing edge detail and texture to upscale high definition content
Electric meters measure the amount of electric current supplied to a shop, house or any other source including machines. The electricity board has different terms and conditions for installing various electric meters depending on their usage. These m
Thinking of going for a Pay As You Go Mobile Phones? Not sure which one to go for? Here his a quick review of each of the best selling Pay As You Go mobile phone. These are the most popular handsets people tend to go for when they go shopping for a n
Even as the market is getting saturated with different HDTV models, several companies are working towards introducing better versions to establish their supremacy. One of the latest innovations of Samsung is LED HDTV. Samsung LED TV is one of the lat
Very few people know that you can actually do people search by phone. Doing a people search by phone can give you access to interesting and helpful facts about any person. If you use the right service, you can even make your very own background check
The techniques utilized in MEMS fabrication borrow from techniques established for the integrated circuit industry, but they have been extended to include production of mechanical components. There are three elements in the conventional processing of
Silicon wafers are actually semiconductor devices that are heavily used in today’s electronics. To some, these micro devices may seem dismissible but they really have important uses in technology. Silicon wafers are primarily used in manufactur
Micro-Electro-Mechanical System - MEMS for short - is a fabrication process that explores potential applications for customized process technologies and processing capabilities of microdevices. In other words, MEMS technology is used to manufacture e
You’ve probably seen, used and taken for granted items that run on microdevices derived through MEMS Processes. Nano-technology may not have your attention, but the mighty power of microdevices drives technology to new heights whether you&rsquo
Silicon is an element that is abundant in nature, is non-metallic and gray, and has a unique characteristic that has helped transform the world we live in. This characteristic is silicon’s ability to conduct electricity. Being able to conduct a
Syndication
tweet
PDF version
Printable version
Publisher HTML version
Discussions (0)
Email Article
Post New Comment